Metal Roofing Contractors Blog | McElroy Metal

How Do You Cut Metal Roofing?

Written by McElroy Metal | Nov 19, 2026 2:00 PM

Cutting metal roofing is something most contractors have done hundreds of times. You’ve probably got your favorite tools and a routine that works for you. But have you ever stopped to think about how the way you’re cutting those panels could affect the finished roof?

A cut that looks fine during installation doesn’t always tell the whole story. Some problems don’t show up until months later, when rust stains start appearing, or the finish begins showing signs of damage.

And then there’s the time and material you can waste making cuts that might not have been necessary in the first place.

Whether you’re working on a simple roof or one with multiple hips, valleys, and vent pipes, a few decisions before making that first cut can make a difference.

What’s the Best Way to Cut Metal Roofing Panels?

Before deciding how to cut a panel, consider whether you need to cut it at all. Most reputable metal roofing manufacturers offer panels cut to specified lengths, eliminating much of the field cutting required during installation.

Think about a straightforward gable roof. If the measurements are accurate and the panels arrive at the correct lengths, there’s little reason to spend time trimming each one on the jobsite. You save labor, reduce the amount of material being handled, and get the benefit of a consistent factory-cut edge.

That’s not to say you’ll never need to make a cut in the field. Even with panels ordered to length, some adjustments are just part of the installation.

What Tools Should You Use to Cut Metal Roofing?

Hand snips, electric shears, nibblers, and profile-matched panel shears are the recommended tools for cutting metal roofing. Which one you use depends on the type of cut you’re making and the panel profile you’re working with.

Hand Snips

For small adjustments, trim work, and tight spaces, hand snips are often all you need. They’re especially useful when you’re working around flashing or making a small cut that doesn’t justify bringing out a power tool.

For example, if you’re fitting a piece of flashing around a plumbing vent, a pair of aviation snips may give you better control than a larger tool. Just make sure the snips are appropriate for the material thickness and the direction of the cut.

Electric Shears and Nibblers

Electric shears work well for longer, straighter cuts, while nibblers are useful when you need to follow an angle or work around an irregular opening.

Imagine you’re cutting panels along a valley. Instead of forcing a tool through the panel’s ribs or struggling to follow the marked line, the right shear or nibbler makes the cut easier to control.

Both tools have their place, but pay attention to the material thickness and panel profile they’re designed to handle. Not every tool will work equally well on every roofing system.

Profile-Matched Panel Shears

If you regularly install exposed fastener panels, you may have used a profile-matched panel shear. If not, picture one of those large paper cutters from art class, except designed to accommodate the ribs of a metal roofing panel.

Instead of cutting across each rib individually, the shear cuts through the panel using a blade and die designed for that particular profile. This can be especially helpful when you’re making repetitive cuts across multiple panels.

Panel shears are available for certain exposed fastener profiles, and some manufacturers or equipment suppliers offer them for purchase or rental.

Why Should You Avoid Circular Saws and Angle Grinders When Cutting Metal Roofing?

Circular saws are commonly found on construction sites, and it’s easy to see why you might reach for one when cutting metal roofing. However, just because a tool can cut through a metal panel doesn’t mean it’s the best choice for the job.

McElroy Metal does not recommend using circular saws to cut metal roofing panels, even when they’re equipped with metal-cutting blades. There are several reasons for this.

  • Damage to protective coatings. Abrasive cutting generates significant heat that can damage the paint and metallic coatings along the cut edge. Once those coatings are compromised, the exposed steel becomes more vulnerable to corrosion.
  • Rust staining from metal filings. High-speed cutting can scatter metal particles across the roof. Those particles may remain on the painted surface and eventually rust, leaving small brown spots that can be mistaken for corrosion of the panel itself.
  • Poor cut quality. Improper cutting methods can leave rough edges, burrs, or coating damage that requires additional attention before installation.
  • Safety concerns. Flying metal chips, noise, and potential kickback add risks that must be considered when using high-speed cutting equipment.

There’s also the potential impact on warranty coverage. Damage resulting from improper cutting methods may not be covered under the manufacturer’s warranty.

The Metal Construction Association’s Metal Roof Installation Manual reinforces the importance of using appropriate cutting methods and cautions against saw cutting because of the potential for coating damage.

That quick cut might save a few minutes today, but it isn’t worth creating a problem that brings you back to the jobsite later.

How Do You Cut Metal Roofing Around Hips, Valleys, and Penetrations?

Before making the first cut, take time to plan the panel layout. Where will the cuts fall? Which edges will be covered by flashing? And can any of the remaining material be used elsewhere on the roof?

For hips and valleys, measure and mark the required angle while accounting for the manufacturer’s flashing details and clearances. Double-check the panel orientation before cutting, particularly when working with standing seam systems.

For pipes, vents, and curbs, the opening needs to accommodate the appropriate flashing or penetration detail. Hand snips and nibblers are often useful for these cuts because they provide control when working around corners and irregular shapes.

The panel profile can also affect your approach. Exposed fastener panels such as Max-Rib and Mega-Rib have ribs you need to accommodate during cutting. Standing seam panels such as Medallion-Lok and 238T require additional attention to seam engagement and the panel’s installed orientation.

Why Do Symmetrical Standing Seam Panels Reduce Waste?

Here’s where symmetrical standing seam panels can offer an advantage.

Let’s say you’re installing panels along a valley. You cut one panel to the required angle, leaving a substantial piece of material behind. With an asymmetrical standing seam panel, that leftover piece may have the wrong seam orientation to work on the opposite side of the roof.

With a symmetrical panel, both sides have matching seam configurations. Depending on the roof layout and cut angle, you may be able to use the remaining piece elsewhere instead of discarding it.

Symmetrical standing seam systems, such as 138T and 238T, offer this flexibility. On roofs with multiple hips and valleys, reusing those leftover pieces can help reduce material waste.

How Do You Protect Metal Roofing After Cutting?

Once you’ve made the cut, remove any metal shavings or debris from the panel surface using a soft brush or another nonabrasive method. Pay particular attention to areas around ribs and seams where small particles can collect.

Next, check the cut edge for burrs or distortion. If you find any, remove them carefully without damaging the surrounding finish. Also inspect the painted surface for scratches or other damage that may have occurred during cutting or handling.

If touch-up paint is needed, follow the manufacturer’s recommendations rather than assuming every scratch or exposed edge should be painted.

Whenever possible, position field-cut edges beneath the appropriate flashing or trim. For example, a cut edge at the ridge may be protected beneath the ridge cap when the installation details allow it.

What Safety Precautions Should You Take When Cutting Metal Roofing?

Sharp edges are part of working with sheet metal, but that doesn’t mean injuries have to be. Cut-resistant gloves, safety glasses, hearing protection, and long sleeves can help protect against common hazards associated with cutting and handling panels. Make sure the tool you’re using is appropriate for the material thickness and that any required guards are in place.

It’s also important to properly support and secure the panel before cutting. Long panels can flex or shift unexpectedly, especially when you’re working alone or trying to make a cut near the edge of a work surface.

Whenever practical, make cuts on a stable surface before moving the panel onto the roof. If cutting at height is necessary, follow the appropriate fall protection procedures and keep your work area clear of loose materials.

A little preparation can make the cutting process safer and help prevent damage to the panels.

The next time you’re preparing to cut a metal roofing panel, consider whether the cut is necessary, whether you’re using the right tool, and what will happen to the remaining material. Those decisions can save time, reduce waste, and help protect the finished roof.

For additional guidance on cutting and installing specific panel profiles, contact McElroy Metal.